Difference between revisions of "An Evaluation of the suitability of colorpHast strips for pH measurements in home brewing"

From German brewing and more
Jump to: navigation, search
(Results and Discussion)
(Results and Discussion)
Line 116: Line 116:
  
 
[[Image:ColorpHast_experiment_chart_mash_and_beer.gif|frame|right|'''Figure 6''' -]]
 
[[Image:ColorpHast_experiment_chart_mash_and_beer.gif|frame|right|'''Figure 6''' -]]
 
<div style="clear:both;"></div>
 
 
[[Image:ColorpHast_experiment_chart_mash_and_beer.gif|frame|left|'''Figure 5''' -]]
 
  
 
<div style="clear:both;"></div>
 
<div style="clear:both;"></div>

Revision as of 19:15, 14 August 2009

EMD's colorpHast strips for the pH range 4.0 to 7.0 are very popular among home brewers. Their more narrow range and improved readability are an improvement over economy pH strips. While they don't provide the precision of a pH meter they don't require the maintenance necessary for the latter and are therefore a very attractive means of testing pH in home brewing.

But earlier studies done by myself have shown that these strips seem to have a systematic error of -0.3 pH. I.e. the strips tend to report a pH reading that is about 0.3 pH less than what is determined with a calibrated pH meter:

Since this error could be the result of lot specific variations I needed a larger sample. To get this larger sample I solicited the help from fellow brewers on the Northern Brewer and HomeBrewTalk.com forms. They sent me a few of their colorpHast strips and I made test mashes and tested these mashes and a sample of beer with these test strips and a pH meter.

In the end it was confirmed that the colorpHast strips have a -0.3 systematic error when they are used for testing the mash pH. No significant error was found for testing beer pH but the range of confidence with which the strip's color could be interpreted was larger than for the mash pH experiments.

Methods and Materials

The test mashes were prepared by mixing 60 C (140F) water with a pulverized grist at a mash thickness of 4 l/kg:

  • mash A: 50% Weyermann Munich II, 50% Weyermann Pilsner, water residual alkalinity = 35 ppm CaCO3
  • mash B: 100% Weyermann Pilsner, water residual alkalinity = 115 ppm CaCO3

The mash temperature was held stable at 60C (140F) for 10 min in a water bath and then the mashes were cooled to 25C (77F) within 5 min in an ice bath. Because of additional delays the samples stood at room temperature for about 20 min before they were tested.

Testing was done with a calibrated pH meter (Milwaukee SM101)and with the colorpHast strips. Once the colorpHast strips were submerged in the samples they were blotted with a paper towel and placed on a piece of white paper along with the color chart that was supplied with my colorpHast strips. A picture was taken with a digital camera in RAW format. The lighting was a tungsten light source. This format only captures the output of the CCD sensor and leaves additional processing to post processing software.

The beer sample was warmed to 25C and because its pH was 4.0 which was too close to the range of the strips its pH was adjusted to 4.4 with a sodium bicarbonate solution. The strips were submerged for about a minute and a picture was taken on white paper in tungsten light.

The images of the strips and the color scale were then color corrected for white balance and adjusted to the same brightness. After that the color scale and the strips were rearranged to fit into a smaller format and presented to the members at the Northern Brewer and HomeBrewTalk forums. The participating users were asked to match the color of each strip to the color scale and read the pH and a confidence range. That data was then plotted.

2 participants made an effort to use a software based color matching technique Their data was plotted as well.

Ken Rubin's technique [Rubin]:

A simple program averages each of the rgb color components within a selected box. 
The average rgb values are then used to determine the "distance" to black by using 
the formula Sqrt(r^2 + g^2 + b^2). 

For the reference colors on the color scale the following distances to black were 
found 

4.0: 273
4.4: 259
4.7: 222
5.0: 163
5.3: 129
5.5: 124
5.8: 110
6.1: 80
6.5: 71
7.0: 65. 

After that the distances to black for each of the test strips were determined  

1: 146
2: 170
3: 168
4: 148
5: 170
7: 159
8: 155
9: 168. 

Using simple interpolation the following pH values were determined for the 
tested strips 

1: 5.15
2: 4.96
3: 4.97
4: 5.14
5: 4.96
7: 5.04
8: 5.07
9: 4.97

A.J deLange's technique [deLange]:

The color meter of the Mac was used to measure color in the L*, a*, b* space. 
It was determined that the b channel was the most sensitive so only that was 
used to compare the strips. 8 channel b readings were taken for each of the 
4.7, 5.0 and 5.3 reference color fields and averaged. A 3rd order polynomial 
that fits the average b-channel readings was dretermined and later used to 
determine the pH reading for each of the tested strips based on their b-channel 
readings. For each of the strips 6 b-channel readings were taken, converted 
to pH using aforementioned polynominal. After running statistics the following 
results were determined

Strip 01 4.95 ± 0.03
Strip 02 5.08 ± 0.04
Strip 03 4.96 ± 0.03
Strip 04 5.05 ± 0.04
Strip 05 4.96 ± 0.03
Strip 07 5.05 ± 0.02
Strip 08 4.89 ± 0.05
Strip 09 4.97 ± 0.07

  

Results and Discussion

Figure 1 - colorpHast strips before they were used
Figure 2 - colorpHast strip after being used in a test mash with a pH of 5.35 at room temperature.
Figure 3 - colorpHast strip after being used in a test mash with a pH of 5.35 at room temperature.
Figure 4 - colorpHast strip after being used in a sample of beer with a pH of 4.40 at room temperature.
Figure 5 -
Figure 6 -

Conclusion

References

[Rubin] Northern Brewer forum post
[deLange] personal correspondence

Acknowledgments