Difference between revisions of "Growing Yeast from a Plate"

From German brewing and more
Jump to: navigation, search
(Before you start)
Line 13: Line 13:
  
 
=Before you start=
 
=Before you start=
 
Make sure that there is no daft or other air movement in your working area. This could blow contaminants into your cultures. Loosen the cap of the vial or tube containing the 1st stage starter wort. This should pull in some air. Tighten the cap again and give it a shake to dissolve some of the oxygen. Since sterility is most important at this stage do not oxygenate the wort with other means that could spoil it. The yeast will also grow without lots of O<sub>2</sub>.
 
  
 
[[Image:Preparing_the_loop.jpg|right]]
 
[[Image:Preparing_the_loop.jpg|right]]
 +
 +
Make sure that there is no daft or other air movement in your working area. This could blow contaminants into your cultures. Loosen the cap of the vial or tube containing the 1st stage starter wort. This should pull in some air. Tighten the cap again and give it a shake to dissolve some of the oxygen. Since sterility is most important at this stage do not oxygenate the wort with other means that could spoil it. The yeast will also grow without lots of O<sub>2</sub>.
  
 
Also undo the tape that keeps the petri dish closed, but keep the lid on.  
 
Also undo the tape that keeps the petri dish closed, but keep the lid on.  
  
 
Using the flame source sterilize the inoculation loop by starting from its end and pulling it slowly through the flame. All parts of the lower half of the loop should have been glowing red. After that open the vial and stick the loop into the wort to cool it off. Otherwise you are going to fry the colonies that you are going to pick next picking.
 
Using the flame source sterilize the inoculation loop by starting from its end and pulling it slowly through the flame. All parts of the lower half of the loop should have been glowing red. After that open the vial and stick the loop into the wort to cool it off. Otherwise you are going to fry the colonies that you are going to pick next picking.
 +
 +
<div style="clear:both;"></div>
  
 
=Picking Colonies=
 
=Picking Colonies=

Revision as of 04:31, 3 March 2008

Growing yeast from a plate (petri dish) allows the brewer to select only a few single cell growth colonies. By doing so a pure culture can be obtained even if the starting culture was questionable. But because the number of yeast cells is very small during the first few steps, a sterile environment is necessary.

What is needed?

Needed for growing yeast.jpg
  • petri dish with yeast colonies (Yeast Cultures on Petri Dishes)
  • inoculation loop
  • flame source. Bunsen burner, alcohol lamp, blow torch or gas stove
  • vial with sterile starter wort

Before you start

Preparing the loop.jpg

Make sure that there is no daft or other air movement in your working area. This could blow contaminants into your cultures. Loosen the cap of the vial or tube containing the 1st stage starter wort. This should pull in some air. Tighten the cap again and give it a shake to dissolve some of the oxygen. Since sterility is most important at this stage do not oxygenate the wort with other means that could spoil it. The yeast will also grow without lots of O2.

Also undo the tape that keeps the petri dish closed, but keep the lid on.

Using the flame source sterilize the inoculation loop by starting from its end and pulling it slowly through the flame. All parts of the lower half of the loop should have been glowing red. After that open the vial and stick the loop into the wort to cool it off. Otherwise you are going to fry the colonies that you are going to pick next picking.

Picking Colonies

Plate w colonies.jpg

In order to ensure that you are only using yeast colonies that have grown from a single yeast cell only consider single round colonies of yeast. Yeas colonies are off-white with dull looking surface. Some of your streaks on the plate should have produced such colonies.