Difference between revisions of "Growing Yeast from a Plate"

From German brewing and more
Jump to: navigation, search
(1st stage propagation)
(1st stage propagation)
Line 49: Line 49:
  
 
{| border="0"  
 
{| border="0"  
|-
+
|-valign="top"
| align="right" |Place the vial in a warm location (18-25 C / 70-80F) for 2 days. During that time you want to keep the cap on only loosely to let the CO<sub>2</sub> escape. Not only are you risking a sudden foam-up when opening the vial by keeping the cap closed tightly, but also are you retarding the yeast growth. Like alcohol, CO<sub>2</sub> is toxic to yeast and the yeast prefers the level of CO<sub>2</sub> to be low.
+
|Place the vial in a warm location (18-25 C / 70-80F) for 2 days. During that time you want to keep the cap on only loosely to let the CO<sub>2</sub> escape. Not only are you risking a sudden foam-up when opening the vial by keeping the cap closed tightly, but also are you retarding the yeast growth. Like alcohol, CO<sub>2</sub> is toxic to yeast and the yeast prefers the level of CO<sub>2</sub> to be low.
 
After days you should see a small kraeusen and some yeast sediment developing. When you shake up the vial (don't forget to close it and re-open it slowly) it will be more milky than before. This is a sign that yeast is gowing. If not, make sure it is warm enough and give it a few more days. If after longer waiting nothing is happening, the yeast was dead.
 
After days you should see a small kraeusen and some yeast sediment developing. When you shake up the vial (don't forget to close it and re-open it slowly) it will be more milky than before. This is a sign that yeast is gowing. If not, make sure it is warm enough and give it a few more days. If after longer waiting nothing is happening, the yeast was dead.
 
| [[Image:Small_kraeusen_1st_stage.jpg|right]]
 
| [[Image:Small_kraeusen_1st_stage.jpg|right]]
 
| [[Image:Yeast_sediment_in_1st_stage.jpg]]
 
| [[Image:Yeast_sediment_in_1st_stage.jpg]]
 
|}
 
|}

Revision as of 05:01, 3 March 2008

Growing yeast from a plate (petri dish) allows the brewer to select only a few single cell growth colonies. By doing so a pure culture can be obtained even if the starting culture was questionable. But because the number of yeast cells is very small during the first few steps, a sterile environment is necessary.

What is needed?

Needed for growing yeast.jpg
  • petri dish with yeast colonies (Yeast Cultures on Petri Dishes)
  • inoculation loop
  • flame source. Bunsen burner, alcohol lamp, blow torch or gas stove
  • vial with sterile starter wort

Before you start

Preparing the loop.jpg

Make sure that there is no daft or other air movement in your working area. This could blow contaminants into your cultures. Loosen the cap of the vial or tube containing the 1st stage starter wort. This should pull in some air. Tighten the cap again and give it a shake to dissolve some of the oxygen. Since sterility is most important at this stage do not oxygenate the wort with other means that could spoil it. The yeast will also grow without lots of O2.

Also undo the tape that keeps the petri dish closed, but keep the lid on.

Using the flame source sterilize the inoculation loop by starting from its end and pulling it slowly through the flame. All parts of the lower half of the loop should have been glowing red. After that open the vial and stick the loop into the wort to cool it off. Otherwise you are going to fry the colonies that you are going to pick next picking.

Picking Colonies

Plate w colonies.jpg

In order to ensure that you are only using yeast colonies that have grown from a single yeast cell only consider single round colonies of yeast. Yeas colonies are off-white with dull looking surface. Some of your streaks on the plate should have produced such colonies.

Picking colonies.jpg

Using the sterile inoculation loop pick one colony at a time and place them into the wort in the vial. Repeat this until you have picked a few colonies. You could also pick only one. This would give you a pitch of yeast grown from a single cell. But I like to mix it up with a few colonies.

Picked colonies.jpg

Close the plate and the vial. If you look at the bottom of the vial, you can see the colonies.

1st stage propagation

Place the vial in a warm location (18-25 C / 70-80F) for 2 days. During that time you want to keep the cap on only loosely to let the CO2 escape. Not only are you risking a sudden foam-up when opening the vial by keeping the cap closed tightly, but also are you retarding the yeast growth. Like alcohol, CO2 is toxic to yeast and the yeast prefers the level of CO2 to be low.

After days you should see a small kraeusen and some yeast sediment developing. When you shake up the vial (don't forget to close it and re-open it slowly) it will be more milky than before. This is a sign that yeast is gowing. If not, make sure it is warm enough and give it a few more days. If after longer waiting nothing is happening, the yeast was dead.

Small kraeusen 1st stage.jpg
Yeast sediment in 1st stage.jpg