Kraeusening

From German brewing and more
Revision as of 19:26, 31 March 2008 by Kaiser (Talk | contribs)

Jump to: navigation, search

Besides corn sugar and DME, beer can also be carbonated with unfermented or actively fermenting wort. This procedure is usually used by breweries that bottle condition their beers. And the reason for this is simple: freshly fermenting wort is readily available in a brewery. It also has several advantaged over the priming corn sugar/DME:

  • the flavor of your beer will not be changed, since you are adding part of the original wort (same IBUs, same malt profile, etc.)
  • the apparent OG will not be changed. (if you use a highly concentrated sugar solution your FG and ABV will be as if the beer had a 2-3 GU higher OG)
  • in the case of Kraeusening fresh and healthy yeast is added which does a better job in scrubbing the beer of O2 and off-flavors. In this case you can also use your bottles as a yeast bank since it is not the least flocculant yeast that is at the bottom of those bottles
  • carbonation times will also be more predictable if you add fresh yeast
  • you will have more beer to bottle and can get 5gal out of using a 5 gal carboy for fermentation.

The main disadvantage is the added complexity.


If you want to prime with Speise (unfermented wort) or Kraeusen (fermenting wort), you want to keep some of the original wort from the brew day. Some brewers just keep it in a jar in the fridge, but I like to store mine in the freezer. This way I don't have to worry about something growing in there for the next 3 weeks that it takes until I bottle. I also don't worry about sanitation when I collect the Speise. As shown in the whirlpool article, I get most of it by filtering the hot-break/hop sludge, that is left in the kettle, through a paper towel.

Once I need it, I will take the Speise from the freezer defrost and boil it for 10 min in a 2000ml Erlenmeyer flask. This will sanitize it. If you need to add more bitterness to the beer, you can also add hops to this boil and boil longer. Chill the wort overnight or in an ice-bath.

If you want to bottle with Kraeusen, you need to inoculate it with yeast. Either add some fresh dry or liquid yeast. I simply take a sanitized racking cane to pull some yeast samples from the fermenter. Close one end of the cane with your thumb and push it all the way to the bottom of the primary or secondary. Open it to suck up some yeast from the bottom. Moving it around while doing this also helps. Close up the end again and move the cane to your starter vessel and dump the yeast in there. Repeat this a few times until you have enough yeast.

Now wait until it starts fermenting.

Calculating the volume

While the calculation of Speise additions is easier, a precise calculation of the amount of Kraeusen needed is more complicated since its fermentation constantly reduces the amount of sugar that is needed. I’ll be showing a simplified equation and a more precise approach. A spread sheet also exists for the more precise approach. All calculations are done in weight % (basically equal to Plato) for the extract and g/l for carbonation. If you are want to use specific gravity and volumes of CO2 you can use these equations to perform the conversion:

% extract = (SG – 1) * 4000

<g/L CO2 = <Volume of CO2 >* 2

simple equation

This is a simplified equation for the needed Kraeusen volume. It assumes

  • 10% apparent attenuation of the Kraeusen
  • 75% apparent fermentability of the Kraeusen
  • The Krauesen volume is not significant compared to the beer volume

VKraeusen = 336 * ( Cfinal * Vbeer - Cbeer * Vbeer - 0.5 * msugar ) / OE





The amount of gyle needed for a batch can be calculated with this formula

Quarts of gyle = (12 x gallons of wort) / (specific gravity - 1)(1000)

(source: http://www.midwestsupplies.com/faq/b...egging_faq.asp)

I requested that a more precise calculation of this (one that accounts for attenuation and already existing CO2 in the beer) is added to BeerSmith.

If you don't add new yeast, the carbonation time should be similar to the use of DME for priming.

In order to bottle with Kraeusen you need to do a little more. Prepare a starter with the calculated amount of gyle plus another pint of gyle. Aerate it and pitch this starter with the yeast you want to use for bottling. There are some advantages of actually using a different yeast that you fermented with. I have heard that some brewers actually bottle lagers with ale yeast. Or you want to choose a very flocculant strain. According to White Labs, no significant amount of flavor will be produced by the yeast used for bottling and ale yeasts work faster too. I usually harvest yeast from the primary and will use the same yeast for bottling.

You want to be ready to bottle when the starter is actively fermenting (at high Kraeusen) but hasn't fermented lots of the sugars yet. The CO2 should end up in the bottle and not in the atmosphere. Once you are ready to bottle, you want to add the desired amount of that starter (see formula above) to your bottling bucket. If you think it has been fermenting for a while already, you can add a little more. Here is the tricky part. You don't really want to get the yeast sediment that is at the bottom of the starter, only the healthy yeast that is currently in suspension is necessary. That's why I suggested adding another pint of gyle when making the starter. Leave that in there and try to pour only once, as tilting it back up will get a lot of that yeast in suspension.

Now add your beer, stir and bottle as usual. Carbonation will be complete in 5-7 days. From my experience there will not be more yeast sediment than using conventional priming methods. But I also keep my secondaries cold (~50F for ales) which causes more of the original yeast to settle out.

The same method is used for carbonating my lagers in a corny keg before I start lagering. But there I just make sure that enough Speise is added to get above the desired CO2 level. I then monitor the pressure build-up and blow-off any excess CO2. This has the advantage of adding fresh and healthy yeast before the lagering is done. Finally I rack it off all the yeast into a serving keg.

Is all this extra work worth the effort? Every brewer has to decide this for himself. Maybe some day I will do a direct comparison between the same batch of beer carbonated with corn sugar, DME and Kraeusen.

Source : http://www.homebrewtalk.com/showthread.php?t=9685